Dacor Dishwasher Repair Cost: DDW24M Parts and Labor Guide
Quick answer
Dacor DDW24M dishwasher repair in Northern Virginia typically runs $150–$650 depending on the fault. Drain pump replacement — the most common repair — runs $200–$380 installed. Control board replacement runs $350–$650. Even at the high end of the repair range, that is 11–19% of the true all-in replacement cost of a panel-ready DDW24M ($1,800–$3,400+ including a new custom panel and installation). Repair is almost always the correct financial decision on an integrated Dacor dishwasher.
Dacor's DDW24M integrated dishwasher is a European-platform appliance built for custom-panel kitchens — common in McLean, Great Falls, Potomac, and Bethesda homes where the dishwasher blends invisibly into custom cabinetry. When it needs repair, two things set the cost conversation apart from a standard dishwasher: (1) the panel-ready installation adds a small labor step (panel removal and reinstall) to any repair, and (2) the true cost of replacement is not the $1,400–$2,200 sticker price — it is that price plus the cost of sourcing and installing a new matching custom panel ($200–$800) and professional installation ($200–$400), which typically brings the real replacement number to $1,800–$3,400 or more. This makes repair the clear financial choice on almost every Dacor dishwasher fault, even when the part being replaced is the control board.
1. Diagnostic visit and what it covers
A Dacor DDW24M repair starts with an on-site diagnostic visit. In Northern Virginia, the diagnostic fee for a specialty dishwasher in a panel-ready installation runs $75–$125. We credit this fee toward the repair if you proceed after the diagnosis. During the diagnostic visit, the technician removes the custom panel (a step most general appliance technicians skip or mishandle on integrated units, which can misalign the door and trigger recurring E15 overflow codes), reads any stored fault codes, runs the dishwasher through test cycles to observe the fault live, and checks the components most likely to have caused the error code. After diagnosis, you receive a written upfront quote for the repair — no work proceeds without your approval.
2. Drain pump replacement: $200–$380 installed
The drain pump is the most common Dacor DDW24M repair. It is the component behind E24 fault codes when filter cleaning does not resolve the error. The drain pump motor fails due to normal wear, a foreign-object strike that cracks the impeller, or prolonged operation with a partially blocked filter. Labor involves pulling the unit forward, removing the base panel, disconnecting the pump wiring harness and drain hose, and installing the OEM replacement pump. On a panel-ready DDW24M, total time is typically 60–90 minutes. Parts run $80–$180 for an OEM Dacor drain pump; installed cost in Northern Virginia is $200–$380. This is 6–11% of the true all-in replacement cost of a panel-ready DDW24M — always worth repairing.
3. Control board replacement: $350–$650 installed
The control board (main PCB) is the highest-cost single repair on a Dacor DDW24M. A board failure can present as multiple simultaneous error codes, a control panel that does not respond, cycles that start but stop mid-program, or a completely dead display despite confirmed power. Control board failure is less common than drain pump failure but becomes more likely on units that have experienced power surges or voltage fluctuations — Northern Virginia thunderstorm season is a frequent trigger. Parts run $200–$450 for an OEM Dacor control board; installed cost is $350–$650. At the high end, this is 19% of the true all-in replacement cost of a panel-ready DDW24M. Still worth repairing on a unit in otherwise good condition.
4. Inlet valve, NTC sensor, and heating element costs
Water inlet valve replacement (E01 fault when filter and supply line are clear) runs $130–$250 installed. The solenoid-operated valve sits at the rear of the unit where the supply line connects; replacement is a 30–45 minute job on a DDW24M. NTC temperature sensor replacement (E09 fault, sensor failure more common than element failure) runs $80–$130 installed — the sensor is a small thermistor in the tub base and is the quickest repair on the dishwasher. Heating element replacement (E09 fault confirmed to the element) runs $160–$300 installed; partial tub disassembly is required. Door gasket replacement (recurring E15 when the tray drained but the fault returned) runs $120–$220 installed; door alignment must be verified after replacement on a panel-ready unit. Circulation pump replacement (inadequate wash pressure, loud circulation noise) runs $280–$450 installed and is the most labor-intensive mechanical repair on the DDW24M.
5. Panel-ready installation: cost impact and what it means for repair
A Dacor DDW24M in a panel-ready installation has a custom cabinet panel attached to the door face, making the dishwasher invisible in the kitchen. This adds $80–$150 to most repairs — not because the repair itself changes, but because the panel must be removed before access and precisely reinstalled at the correct height and gap settings afterward. Door alignment matters on an integrated dishwasher: a panel reinstalled even slightly high or low can cause the door latch to misread, the door gasket to seal unevenly, or the overflow float to trigger recurring E15 codes. A technician experienced with panel-ready integrated dishwashers completes panel removal and reinstall as part of the service call; a technician unfamiliar with integrated units may skip the procedure, leave the panel misaligned, or disturb the door settings. When requesting service on a Dacor DDW24M, confirm the technician has experience with panel-ready integrated dishwashers before scheduling.
When to Call a Specialist
We service Dacor DDW24M integrated and panel-ready dishwashers across McLean, Great Falls, Vienna, Arlington, Fairfax, Falls Church, Reston, Bethesda, Chevy Chase, and Potomac. Our technicians are familiar with the DDW24M panel removal and door alignment procedure, and we carry OEM drain pumps, inlet valves, NTC sensors, and control boards for same-visit evaluation. Flat-rate diagnostic ($75–$125, credited toward repair), written upfront quote before any work begins, 90-day parts and labor warranty on all repairs. Call (571) 571-1664.
Frequently Asked Questions
How much does Dacor dishwasher repair cost in Northern Virginia?
Dacor DDW24M dishwasher repair in Northern Virginia runs $150–$650 depending on the fault. Drain pump replacement (most common, E24 code) costs $200–$380 installed. Control board replacement (multiple codes or dead panel) costs $350–$650 installed. Inlet valve, NTC sensor, and door gasket repairs range from $80–$250 installed. Panel-ready installations add $80–$150 for panel removal and reinstall. The diagnostic fee ($75–$125) is credited toward any repair.
Is it worth repairing a Dacor DDW24M dishwasher?
Almost always yes. The true replacement cost of a panel-ready Dacor DDW24M — dishwasher plus matching custom panel plus professional installation — runs $1,800–$3,400 or more. Even the highest single repair (control board at $650) is 19% of that. Drain pump replacement at $200–$380 is 6–11% of replacement cost. Unless the dishwasher has multiple simultaneous failed components on a unit over 15 years old, repair is the correct financial decision.
Do you repair Dacor panel-ready dishwashers in McLean and Great Falls?
Yes. We service Dacor DDW24M panel-ready integrated dishwashers across McLean, Great Falls, and Northern Virginia. Panel-ready integrated dishwashers require technicians familiar with the custom-panel removal and door realignment procedure — we handle this as part of every service call. Upfront pricing, OEM parts, 90-day parts and labor warranty. Call (571) 571-1664.
Rather have us handle it?
Same-day dishwasher repair across Northern Virginia & DC. Upfront pricing, 90-day warranty, specialist technicians.
Call (571) 571-1664Related
More Dacor Repair Guides